Hyperion g – read user manual online or download in PDF format. Pages in total: The Hyperion g linear imaging scanner boasts class-leading durability. Compatible with Remote MasterMind scanning management software. View and Download Honeywell Hyperion g user manual online. General Purpose Handheld Linear Scanner. Hyperion g Scanner pdf manual.
|Published (Last):||27 November 2012|
|PDF File Size:||13.21 Mb|
|ePub File Size:||14.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
Sends numeric characters as if entered from a numeric keypad. If this is the case, select the code page with which the bar codes were created.
Page This includes but is not limited to: If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. Page 9 Trigger Commands Page 11 – Access the Honeywell web site at www.
Click on the Resources tab. Automatic Caps Lock is used if you change the Caps Lock key on and off.
Honeywell Hyperion g User Manual – Page 1 of 12 |
Page of Go. Page 83 If this bar code is read: This action first clears all current prefixes, then programs a Code I. Code 93 must be enabled to use this example. Fast intuitive bar code reading out to 18 inches mm.
Video Reverse Video Reverse is used to allow the scanner to read bar codes that are inverted. Tighten the two screws to secure the connector to the port. When in serial mode, the scanner scans until a bar code has been read or until the deactivate command is sent. Page 8 – Access the Honeywell web site at www. Honeywelk selections in the following pages are used only if you wish to alter the output.
Chapter 12 – Customer Support For our mqnual contact information, please check our website at 1300gg link above. Page 95 are read, deleting the first space from each.
Related Products and Solutions. User Guides and Manuals. When Check Character is set to Majual and Transmit, the scanner will only read MSI bar codes printed with the specified type check character, and will transmit this character at the end of the scanned data.
Both the serial commands and the programming bar codes will pro- gram the scanner. When turned off, there is no space.
Table of Contents Add to my manuals Add. Set the length in milliseconds for a timeout by scanning the bar code below, then setting the timeout from 1- milliseconds by scanning digits from the inside back cover, then scan- ning Save.
Honeywell Hyperion 1300G User Manual
Refer to Chapter 9 for settings and defaults. Scan the Add Prefix or Add Suffix symbol page Page 2 Disclaimer Honeywell International Inc.
If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.
The information in this publication does honeywelp repre- sent a commitment on the part of HII. Programming Chart Honeyaell Discard Note: Codabar Concatenation Codabar supports symbol concatenation.
Page 78 The data is output as: To remove this delay, scan the Delay Length bar code, and set the number of steps to 0. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. User-specified Reread Delay User-Specified Reread Delay If you want to set your own length for the reread delay, scan the bar code below, then set the delay frommilliseconds by scanning digits from the inside back cover, then scanning Save. If you are having unexpected results with this programming code, scan Resetting the Custom Defaults Beeper Pitch — Good Read The beeper pitch codes modify the pitch frequency of the beep the scanner emits on a good read.
Enter text from picture: Summary of Contents for Honeywell G-2 Page 1 With no moving parts to wear out, the Hyperion g is one of the toughest general duty scanners on the market.
Honeywell Productivity and Workflow Solutions
Symbologies Introduction This programming section contains the following menu selections. Even better, it eliminates the need to buy specialty scanners. Don’t show me this message again. Beeper Pitch – Error Beeper Pitch — Error The beeper pitch codes modify the pitch frequency of the honeywrll the scanner emits when there is a bad read or error. See the Symbology Charts page A-1 for the single character code that identifies each symbology.
Honeywell Hyperion 1300g Quick Start Manual
Enter text from picture: Both the serial commands and the programming bar codes will pro- gram the scanner. Interfunction Delay To remove this delay, scan the Delay Length bar code, and set the number of steps to 0. For complete descriptions and examples of each serial pro- gramming command, refer to the corresponding programming bar code in this manual. Page 85 If this bar code is read: