ASTM D – Air Permeability of Textile Fabrics . ASTM D – Standard Test Method for Flexural Properties Testing of Unreinforced and Reinforced. The Flexural test ASTM D measures the force required to bend a plastic beam under a four point loading system. The test method is used for reinforced or . ASTM D tests flexural properties of unreinforced and reinforced plastics and electrical insulating materials by four point bending. Learn more.

Author: Dajin Gadal
Country: Slovenia
Language: English (Spanish)
Genre: Love
Published (Last): 22 July 2004
Pages: 493
PDF File Size: 8.42 Mb
ePub File Size: 4.79 Mb
ISBN: 523-2-47183-582-4
Downloads: 3046
Price: Free* [*Free Regsitration Required]
Uploader: Brakasa

Do not use the movement of the loading noses relative to the supports. Repeatability of calculations — When setting up the test, having an adequate preload is highly recommended to ensure accurate and consistent strain measurements. For specimens less than 2. Calculation NOTE 11—In determination of the calculated value of some of the properties listed in this section it is necessary to determine if the toe compensation see Annex A1 adjustment dd6272 be made.

Anyone wishing to participate in this work may contact the Chairman of Section D In three point bending the maximum axial fiber stress is located immediately under the loading nose. If you feel that your d272 have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. We use cookies to improve your browsing experience.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement ast such rights, are entirely their own responsibility.

NOTE 7—Where machine sensitivity is such that specimens of these dimensions cannot be measured, wider specimens or shorter support spans, or both, may be used, provided the d66272 span-to-depth ratio is at least 14 to 1. This test method covers the determination of unreinforced and reinforced plastics, including high-modulus composites and electrical insulating materials in the form of rectangular bars molded directly or cut from sheets, plates or molded shapes.


The series of extensometers offers speed of attachment and ease-of-use. Subscribe to Our Newsletters. This parallelism may be checked by means of a plate containing parallel grooves into which the loading noses and supports will?

Subscribe to Instron News! For the four point flexural test, the specimen lies on a span and stress is uniformly distributed between the loading noses. The second generation Advanced Video Extensometer AVE 2 utilizes patented measurement technology axtm the fastest, most accurate non-contacting strain measurement device commercially available. It is an artifact caused by a takeup of slack and alignment or seating of the specimen.

The elastic modulus can be determined by dividing the stress at any point along the Line CD or its extension by the strain at the same point measured from Point B, de?

See Annex A2 for information on the determination of and setting of the span. This standard is subject to revision at any time by the responsible f6272 committee and must be reviewed every? Current edition approved July 10, Alternatively, slack correction can be used to ensure that the calculations are performed on the appropriate section of the testing data. NOTE 16—This value may differ from?

NOTE 2—Test data have shown that the loading noses and support dimensions can in?

The selected point is generally chosen at a speci? A support span-to-depth ratio of The AutoX is a high-resolution, long-travel automatic contacting extensometer. The light-weight, rugged cross-brace design eliminates errors caused by physical distortion, while built-in protection ensures that damage is not caused by over-extension.

ASTM D6272

In this case, it is suggested that yield strength, if applicable, be calculated and that the corresponding strain be reported also see Make appropriate corrections for indentation in the specimens and de?

These solutions require little influence aetm the operator, resulting in improved repeatability. Overhang shall be sufficient to prevent the specimen from slipping through the supports. For all tests, atm support span shall be 16 tolerance 6 1 times the depth of the beam. All dimensions must be stated in the report see also Note 6.


Please confirm that you agree with our privacy and cookies policy to submit this form. Users qstm previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Onsite Training At Your Facility. Use the measured span for d62722 calculations. Concrete, Asphalt and Rock. Thicker specimens should be avoided if they exhibit signi?

Flexural Properties by Four-Point Bending ASTM D

Select from list below: Z shall equal 0. Retests asfm be made for any specimen on which values are not calculated. If specimen depth exceeds the width, buckling may occur. These test methods are generally applicable to rigid and semirigid materials. These measurements shall be made in accordance with Test Method D The distance between the loading noses the load span is either one third or one half of the support span see Fig. All width and thickness measurements of rigid and semi-rigid plastics may be measured with a hand micrometer with ratchet.

Center the specimen on the supports, with the long sstm of the specimen d62722 to the loading noses and supports. Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more!