ALLEN BRADLEY 1305 VFD MANUAL PDF

However, using an Allen-Bradley motor with your drive removes the . Н Installation guidelines called out in Appendix D of the User’s Manual. Installation Instructions IN. May, Allen-Bradley. Dynamic Brake. Cat. No. KAA KBA03, KBA06, KBA Table of Contents. Find great deals for Allen Bradley Adjustable Frequency AC Drive User Manual. Shop with confidence on eBay!.

Author: Vujinn Arashitaur
Country: Namibia
Language: English (Spanish)
Genre: Automotive
Published (Last): 17 November 2010
Pages: 88
PDF File Size: 16.55 Mb
ePub File Size: 5.55 Mb
ISBN: 340-3-52163-721-7
Downloads: 74321
Price: Free* [*Free Regsitration Required]
Uploader: Kezshura

Check the external potentiometer circuit at TB2, terminals 1, 2, and 3 for a disconnected current. Error 5 – Drive is running while attempting download Repeat operation.

Allen Bradley Adjustable Frequency AC Drive User Manual | eBay

Unplug the HIM from the cable or drive and reconnect it. Serial Fault – F10 An active alllen bus adapter is disconnected while it possesses control of a local bus function. Verify that all parameters have been programmed. Check the AC line for high line voltage or transient conditions.

Overtemperature Fault – F8 Temperature sensor detects excessive heat. Inspect for breaks in communications line. Motor Stall Fault – F6 The motor has stalled If the motor is drawing excessive current, the motor load is excessive and will not allow the drive to accelerate to set speed. Replace the Communication cable. Change [Cable Length] to “Long” if applicable. Check for a short circuit at the drive output or excessive load conditions at the motor.

Inspect the motor and external wiring to the drive output terminals for a shorted condition. Error 4 – Saved data for parameter not correct for new drive. D Micro Programmable Logic Controllers. Inspect for blocked or contaminated heat sink fins. Overload Fault – F7 Internal electronic overload trip.

  ARISTOTELIS NIKOMACHO ETIKA PDF

Capabilities of drive are different than the master drive. DC Bus voltage fell below the minimum value. Phase V Fault – F39 A phase to ground fault has been detected between the drive and motor in this phase. An external pot is connected and the ground lead of the pot is disconnected, creating a potential drive overspeed hazard.

The last parameter programmed will be displayed on the top line. Drive Reset Fault – F22 May occur on power-up.

Check for external noise sources. Overspeed Fault – F25 Internal error.

Allen Bradley 1305 Adjustable Frequency AC Drive User Manual

Unplug the HIM from the cable or drive, then reconnect it. Check motor for grounded phase. Overcurrent Fault – F12 Overcurrent is detected in overcurrent hardware trip circuit. Press Enter to continue download. Check cable connection from main control board to power board. Check for excess load, improper DC boost setting, DC brake volts set too high or other causes of excess current.

Verify that the parameter has been programmed correctly. Please select the Repairs tab for more information or to request a quote. Correct the cause of the fault and manually clear by cycling the stop command or cycling power. An active mnaual bus adapter is disconnected while it possesses control of a local bus function. Connect proper adapter or change active frequency source. Hz Err Fault – F29 No valid operating frequency.

Allen Bradley Adjustable Frequency AC Drive AB

Phase W Fault – F40 A phase to ground fault has been detected between the drive and motor in this phase. Allfn drive, then re-run download. An attempt has been made to set the [Run Boost] parameter to a value greater than the [Start Boost] parameter. Reset to Default Parameters and Cycle power. Aplen not, manually program any remaining parameters. Reset your drive to the factory default settings.

  BORGES EL JARDIN DE SENDEROS QUE SE BIFURCAN PDF

Skip frequencies and skip bandwith eliminate all operating frequencies. Check [Minimum Freq] and [Maximum Freq] parameters. DC Braking cannot be used with a synchronous motor. Extend the deceleration time or instal dynamic brake option.

1305 AC Drives

Download can only occur with the same type of drive. May occur on power-up.

Inspect for short at the drive output or excessive load conditions on the motor, especially cable capacitance to ground. Check for broken wires, loose connections, or transducer loss at mA input, TB2.

Error 3 – Download was attempted to a different type drive i. Error 2 – The number of parameters in saved profile mannual not equal master number. The Adjustable Frequency AC Drive is a variable speed drive designed to control the speed of three-phase AC induction motors in a variety of demanding applications where flexibility, performance and ease of use vgd essential. If the motor is drawing excessive current, the motor load is excessive and will not allow the drive to accelerate to set speed.

Check the motor for grounded phase.